The following table lists the parameters you can use to configure IPv4 wired network.
Parameter | mwanConnectionMode |
---|---|
Description | It configures the Internet port type for IPv4 wired network. |
Permitted Values | DHCP NOIP Static NOIP |
Default | DHCP NOIP |
Web UI | Network > WAN > WAN IP Mode |
Phone UI | Menu > Advanced > Network > WAN Port > IPv4 > Mode |
WAN IP Mode:
Static IP - Set the IP Address, Subnet Mask and Default Gateway provided by your ISP.
DHCP - IP Address, Subnet Mask and Default Gateway will be issued by the local DHCP Server.
PPPoE - Set the PPPoE Account and PPPoE Password provided by your ISP.
NAT - The product will be the same as a router.
Bridge - The LAN port is the same as the WAN port.
Parameter | DBID_WAN_REQUEST_BROADCAST_REPLY |
---|---|
Description | Note: It works only if “mwanConnectionMode” is set to DHCP |
Permitted Values | 0-Disable 1-Enable |
Default | 0 |
Web UI | Network > WAN > Request broadcast replies |
Parameter | mwan_is_mac_clone |
---|---|
Description | If it is enabled, you can clone the MAC addresses of other devices or the PC and use the MAC address. Note: It works only if “mwanConnectionMode” is set to DHCP |
Permitted Values | 0-Disable 1-Enable |
Default | 0 |
Web UI | Network > WAN > MAC Address Clone |
Parameter | mwan_ipaddr |
---|---|
Description | It configures the IPv4 address for the wired network. Note: It works only if “mwanConnectionMode” is set to Static. |
Permitted Values | IPv4 Address |
Default | Blank |
Web UI | Network > WAN > IP Address |
Phone UI | Menu > Advanced > Network > WAN Port > IPv4 > IP Address |
Parameter | mwan_netmask |
---|---|
Description | It configures the IPv4 subnet mask for the wired network. Note: It works only if “mwanConnectionMode” is set to Static. |
Permitted Values | Subnet Mask |
Default | Blank |
Web UI | Network > WAN > Subnet Mask |
Phone UI | Menu > Advanced > Network > WAN Port > IPv4 > Mask |
Parameter | mwan_gateway |
---|---|
Description | It configures the IPv4 default gateway for the wired network. Note: It works only if “mwanConnectionMode” is set to Static IP. |
Permitted Values | IPv4 Address |
Default | Blank |
Web UI | Network > WAN > Default Gateway |
Phone UI | Menu > Advanced > Network > WAN Port > IPv4 > Gateway |
Parameter | mdns_mode |
---|---|
Description | It configures the IPv4 default gateway for the wired network. Note: It works only if “mwanConnectionMode” is set to DHCP. |
Permitted Values | 0-Off, the phone will use the IPv4 DNS obtained from DHCP. 1-On, the phone will use manually configured static IPv4 DNS |
Default | 0 |
Web UI | Network > WAN > DNS Mode |
Phone UI | Menu > Advanced > Network > WAN Port > IPv4 > Static DNS |
Parameter | mwan_primary_dns |
---|---|
Description | It configures the primary IPv4 DNS server for the wired network. Note: It works only if “ipv6_enabled” is set to 0 (IPv4) or 1 (IPv4 & IPv6). In the DHCP environment, you need to make sure “mdns_mode” is set to 1 (On). |
Permitted Values | IPv4 Address |
Default | Blank |
Web UI | Network > WAN > Primary DNS |
Phone UI | Menu > Advanced > Network > WAN Port > IPv4 > Pri.DNS |
Parameter | mwan_secondary_dns |
---|---|
Description | It configures the secondary IPv4 DNS server for the wired network. Note: It works only if “ipv6_enabled” is set to 0 (IPv4) or 1 (IPv4 & IPv6). In the DHCP environment, you need to make sure “mdns_mode” is set to 1 (On). |
Permitted Values | IPv4 Address |
Default | Blank |
Web UI | Network > WAN > Secondary DNS |
Phone UI | Menu > Advanced > Network > WAN Port > IPv4 > Sec.DNS |
Author:admin Create time:2023-08-23 09:28
Last editor:admin Update time:2024-07-29 16:00
Last editor:admin Update time:2024-07-29 16:00