The following table lists the parameters you can use to configure the SIP Settings.
| Parameter |
DBID_SIP_T1_TIME |
| Description |
It configures the SIP session timer T1 (in ms). |
| Permitted Values |
Integer |
| Default |
500 |
| Web UI |
FXS > SIP Settings > SIP Parameters > SIP Parameters > SIP T1 |
| Parameter |
DBID_MAX_FORWARD |
| Description |
It configures the number of hops through the sip server. |
| Permitted Values |
Integer |
| Default |
70 |
| Web UI |
FXS > SIP Settings > SIP Parameters > SIP Parameters > Max Forward |
| Parameter |
DBID_REG_USERAGENT_NAME |
| Description |
It configures the suffix of User-Agent in SIP request messages from the phone. |
| Permitted Values |
String |
| Default |
Blank |
| Web UI |
FXS > SIP Settings > SIP Parameters > SIP Parameters > SIP User Agent Name |
| Parameter |
DBID_MAX_AUTHEN |
| Description |
It configures the maximum number of authentication failures. |
| Permitted Values |
Integer |
| Default |
2 |
| Web UI |
FXS > SIP Settings > SIP Parameters > SIP Parameters > Max Auth |
| Parameter |
DBID_SIP_REG_RETRY_INTERVAL |
| Description |
It configures the re-registration period (in seconds) after the account registration fails. |
| Permitted Values |
Integer |
| Default |
30 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > Reg Retry Intvl |
| Parameter |
DBID_SIP_REG_LONG_RETRY_INTERVAL |
| Description |
It configures the maximum time to wait (in seconds) for the ATA to retry to re-register after the account registration fails. |
| Permitted Values |
Integer |
| Default |
1200 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > Reg Retry Long Intvl |
| Parameter |
DBID_AVT_MARK |
| Description |
If it is enabled, all AVT tone packets are set with flag bits. If it is disabled, only the first packet sets the flag bit for each DTMF event. |
| Permitted Values |
0-Disable
1-Enable |
| Default |
1 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > Mark All AVT Packets |
| Parameter |
DBID_RFC2543_CALLHOLD |
| Description |
It enables or disables the ATA to use RFC 2543 (c=0.0.0.0) outgoing hold signaling. |
| Permitted Values |
0-Disable, SDP media direction attributes (such as a=sendonly) per RFC 3264 is used when placing a call on hold.
1-Enable, SDP media connection address c=0.0.0.0 per RFC 2543 is used when placing a call on hold. |
| Default |
1 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > RFC 2543 Call Hold |
| Parameter |
DBID_SIP_SERVICE_TYPE |
| Description |
It is used for the fixed IP PBX platform. Currently, only BroadSoft, AlCaTel, and MetaSwitch are supported. |
| Permitted Values |
0-Common
1-BroadSoft
2-AlCaTel
3-MetaSwitch |
| Default |
0 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > Service Type |
| Parameter |
DBID_SIP_DNS_REFRESH_CHECK_TIME |
| Description |
It configures the refresh interval during DNS resolution. |
| Permitted Values |
Integer |
| Default |
0 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > DNS Refresh Timer |
| Parameter |
DBID_SIP_TLS_VERSION |
| Description |
It configures the TLS version to use for handshake negotiation between the ATAe and server (for example, SIP registration server, provisioning server). |
| Permitted Values |
0-TLS 1.0
1-TLS 1.1
2-TLS 1.2 |
| Default |
2 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > TLS Version |
| Parameter |
DBID_SIP_IPMODE |
| Description |
It configures the network transfer protocol used when the ATA is registered. |
| Permitted Values |
0-IPv4
1-IPv6
2-IPv4 & IPv6 |
| Default |
0 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > IPv4/IPv6 |
| Parameter |
DBID_SIP_SINGLE_PORT |
| Description |
This function is used for multiple FXS ports. If it is enabled, all FXS ports use the same SIP port. |
| Permitted Values |
0-Disable
1-Enable |
| Default |
0 |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > SIP Parameters > All Lines Single SIP Port |
| Parameter |
DBID_SIP_REG_RETRY_RESPCODE |
| Description |
This parameter is used together with “DBID_SIP_REG_RETRY_INTERVAL”.When the value returned by the server is the value of “DBID_SIP_REG_RETRY_RESPCODE”, then the registration will be requested in the “DBID_SIP_REG_RETRY_INTERVAL” period. |
| Permitted Values |
Integer |
| Default |
Blank |
| Web UI |
SIP Account > SIP Settings > SIP Parameters > Response Status Code Handling > Retry Reg RSC |
| Parameter |
DBID_STUN_ENABLE |
| Description |
It enables or disables the STUN (Simple Traversal of UDP over NATs) feature. |
| Permitted Values |
0-Disable
1-Enable |
| Default |
0 |
| Web UI |
SIP Account > SIP Settings > NAT Traversal > NAT Traversal > NAT Traversal |
| Parameter |
DBID_STUN_FRESH_TIME |
| Description |
It configures the refreshing interval of NAT traversal. |
| Permitted Values |
Integer |
| Default |
60 |
| Web UI |
SIP Account > SIP Settings > NAT Traversal > NAT Traversal > NAT Refresh Interval (sec) |
| Parameter |
DBID_STUN_SERVER_IP |
| Description |
It configures the IP address or domain name of the STUN server.
Note: It works only if “DBID_STUN_ENABLE” is set to 1 (Enable). |
| Permitted Values |
String |
| Default |
Blank |
| Web UI |
SIP Account > SIP Settings > NAT Traversal > NAT Traversal > STUN Server Address |
| Parameter |
DBID_STUN_SERVER_PORT |
| Description |
It configures the refreshing interval of NAT traversal. |
| Permitted Values |
Integer |
| Default |
3478 |
| Web UI |
SIP Account > SIP Settings > NAT Traversal > NAT Traversal > STUN Server Port |
Author：admin Create time：2023-11-24 14:15
Last editor：admin Update time：2024-01-03 16:20
